• Cisco Switch Firmware Download
• Hp 5500 Switch Configuration
• Hp 5500 Switch

Update switch firmware from either the Moonshot iLO CM firmware CLI, or from the switch CLI.

Cisco Switch Firmware Download

HP Designjet 5500 Printer - Firmware History. System software (firmware) version S.56.01. System software (firmware) version: S.06.02. Below is the complete history of the HP Designjet 5500 series system software (firmware) releases, with the list and the explanation of the fixed issues and the added functionality. (firmware) download. HP ProCurve Switch Software Access Security Guide 3500 switches 3500yl switches 5400zl switches 6200yl switches 6600 switches 8200zl switches.

NOTE: Firmware files for the switches are included in the Moonshot Component Pack zip file but are not located inside the nested firmware file zip (cp<XXXXXX>.zip). This allows you use HP SUM to update all Moonshot System firmware except for switch firmware files. Switch firmware updates must be done from either the Moonshot iLO CM firmware CLI or from the switch CLI.

IMPORTANT: Moonshot iLO CM firmware CLI updates are compatible with the following switches: Moonshot-45G Switch Module Moonshot-180G Switch Module To update the firmware for an Moonshot-45XGc Switch Module, you must access the switch CLI. See Updating HPE Moonshot-45XGc Switch Module firmware.

​

1. Access the Moonshot iLO CM firmware CLI. For more information, see Connecting CLI sessions.

2. Enable TFTP transfers by entering the enable tftpenable tftp command.

   For example:

3. (Optional) If needed, copy the firmware file to the Moonshot iLO CM firmware flash repository by entering the add firmware fileadd firmware file command.

   For example:

4. Update the switch firmware by entering the update firmwareupdate firmware command.

   For example:

   NOTE: The uploaded filename used in the add firmware file command may not be the same as the filename used in the subsequent update firmware command. Enter the show firmware files command to display the name you must use with the update firmware command.

5. Power off and then power on the switch by entering set switch power commands.

   For example:

6. Following standard security precautions, disable TFTP access by entering the disable tftp command.

​

To access the switch CLI interface:

1. Connect one end of a serial cable to the serial port on the Moonshot Uplink Module and the other end to a laptop or other local machine.

2. On the local machine, start PuTTY. Choose Serial as the connection type, and configure the settings (115200/8-N-1):

   ​

   PuTTY Configuration

3. Click to start the switch CLI session.

Copy the switch firmware file using TFTP, SFTP, or SCP. This example uses TFTP.

Hp 5500 Switch Configuration

Before you begin: ​ Verify that the current switch module firmware is earlier than the version included in this Moonshot Component Pack using the show bootvar command. Your component may already have the latest firmware installed. Verify communication with the TFTP server with an RCMP ping.

​

1. Copy the firmware image from the TFTP server to the alternate firmware bank of the switch:

   copy tftp://<ip_address>/<path>/<filename> alternate

   For example:

2. Configure the switch to boot from the alternate image:

3. Verify the switch boot information:

   The output for this command displays the primary, alternate, current-active, and next-active firmware file versions.

4. Reset the switch and boot from the new image:

5. After the switch finishes rebooting, verify that the firmware update was successful:

   The output for this command shows that the switch boots the image from the alternate flash file system, but the image loads and runs in the primary flash file system.

6. Make a backup of the image:

   NOTE: This removes the ability to downgrade the firmware to the previously installed version. Confirm that you are satisfied with the firmware before running this command.

Hp 5500 Switch

Copy the switch firmware file using TFTP, SFTP, or SCP. This example uses TFTP.

Before you begin: ​ Verify that the current switch module firmware is earlier than the version included in this Moonshot Component Pack using the display version command. Your component may already have the latest firmware installed. • TS-Tune Center offers about 200 settings, for tuning your windows. Hp compaq d530 sff sound drivers windows 7. Verify communication with the TFTP server with an RCMP ping.

​

1. Copy the Moonshot-45XGc Switch Module firmware file to a local TFTP, SFTP, or SCP share.

2. Load the Moonshot-45XGc Switch Module firmware file into the switch from TFTP, FTP, or SCP.

   ​

   Command example (FTP):

   ​

3. Load the firmware by entering the boot–loader command.

   <HP> boot-loader file flash:/<Moonshot-45XGc Switch Module firmware> slot 1 main

4. Reboot the switch by entering the reboot command.

   <HP> reboot